| 精密电阻 | precision resistor | IEC 60115-1 | resistor that is specified with a tighter tolerance on its nominal resistance and/or a lower temperature coefficient of resistance compared to typical standard tolerance and TCR of resistors made with the same product technology, and which in its prescribed testing meets tighter stability requirements than what is usually met by resistor made with the same product technology. |
| 相较于采用同种制造工艺的常规电阻器,标称阻值初始偏差更严苛、和/或电阻温度系数更小,且在规定试验中,稳定性指标也高于同工艺常规产品要求的电阻器。(例:初始偏差1%的线绕功率电阻;电阻温度系数25×10-6/K、公差1%的小功率膜式电阻;阻值小于10 mΩ、电阻温度系数50×10-6/K、公差1%的金属箔电阻) |
| 低值电阻 | low resistance | IEC 60115-1 | resistance for which the predictable error when measured with a conventional two-wire sensing method is significant in comparison to the required precision or to the stated tolerance |
| IEC 62812 | 采用常规两线测量法测量时,可预见的测量误差相较于要求测量精度或标称初始偏差而言不可忽略的电阻 |
| 低功率电阻 | low-power resistor | IEC 60115-1 | resistor that, when loaded with its rated dissipation at the rated temperature, without any accessory supporting dissipation and subjected to natural convection only, maintains a maximum element temperature of 200 ℃ or less. |
| 在额定温度下施加额定功耗,无任何附加辅助散热装置、仅依靠自然对流散热时,元器件最高温度不超过200 ℃的电阻。(额定功耗通常不大于3 W;适用温度范围的限制规定,可使环境试验完整覆盖全部适用温度区间) |
| 标称阻值Rn | nominal resistance | IEC 60115-1 | designated resistance value, usually indicated on the resistor. |
| GB/T 5729 | 电阻器设计所确定的、通常在电阻器上标出的阻值。(英文使用rated resistance) |
| 额定阻值Rr | rated resistance | IEC 60115-1 | resistance value for which the resistor has been designed, and which is generally used for the denomination of the resistor. |
| (The definition of rated resistance is identical to the definition of nominal resistance. Therefore, the nominal resistance can be applied in all cases where a rated resistance is called for) |
| 电阻器设计时的电阻值,一般也用作该电阻器的标称规格(额定阻值在定义上与标称阻值完全一致,因此在所有需要采用额定阻值的常昊,均可使用标称阻值替代) |
| 初始偏差ΔRn | tolerance/tolerance on nominal resistance | IEC 60115-1 | permissible relative deviation of the actual resistance R at 20 ℃ from the nominal resistance Rn at 20 ℃ at the moment of delivery from the manufacturer. |
| (Tolerance on nominal resistance does not account for any change of resistance occurring after delivery form the manufacturer and particularly does not describe any budget for changes the resistor naturally will accumulate under the influence of electrical, environmental and other stresses experienced in its application) |
| 制造商交付时,在20 ℃温度条件下,电阻实际阻值 R 相对于20 ℃下标称阻值 Rn 允许的相对偏差 |
| (初始偏差不包含交付后产生的任何阻值变化,尤其不能用来衡量电阻在使用过程中受电应力、环境应力及其他应力1作用而逐步累积的阻值变动余量) |
| 电阻温度系数α | temperature coefficient of resistance (TCR) | IEC 60115-1 | reversible relative variation of resistance between two given temperatures divided by the difference in the temperature producing it. |
| (The TCR is usually determined between the reference temperature and the LCT/UCT, respectively, for which the larger of the two determined coefficients is expressed as the result. TCR通常分别在基准温度与类别上下限温度之间测定,取两个测定系数中数值更大者作为最终结果) |
| GB/T 5729 | 两个规定温度之间的阻值相对变化除以产生这个变化的温度之差。(缺少对于可逆的描述) |
| 类别温度范围 | category temperature range | IEC 60115-1 | range of ambient temperatures, for which the resistor has been designed to operate continuously, given by the lower and upper category temperature. |
| upper category temperature (UCT): maximum ambient temperature at which a resistor has been designed to operate continuously at the portion of the rated dissipation indicated in the category dissipation. |
| lower category temperature (LCT): minimum ambient temperature at which a resistor has been designed to operate continuously. |
| GB/T 5729 | 电阻器设计所确定的能够连续工作的环境温度范围,该范围取决于它的相应类别的温度极限值。 |
| 上限类别温度(UCT):电阻器设计所确定的、用类别功耗标出的那部分额定功耗下能够连续工作的最高环境温度。 |
| 下限类别温度(LCT):电阻器设计所确定的能够连续工作的最低环境温度。 |
| 温升Δθ | temperature rise | IEC 60115-1 | 电阻施加功耗后,其表面或内部产生的温度升高量;温升大小由电阻自身热特性决定,也就是电阻向环境散出损耗热量的能力。 |
| 功率系数 | power coefficient of resistance (PCR) | 暂无标准定义 | the relative change in resistance when the resistor changes unit power. |
| 电阻在改变单位功率时,阻值的相对变化量。 |
| 热电势 | thermoelectric e.m.f | IEC 62812 | potential difference occurring at the junctions of dissimilar conductors when a temperature difference exists between the junctions. |
| 当异种导体的两处接点之间存在温差时,在接点处产生的电位差。 |
| 额定功耗Pr | rated dissipation | IEC 60115-1 | maximum permissible dissipation at a rated temperature under the conditions of an endurance test and of the respective acceptance criteria. |
| GB/T 5729 | 在70 ℃环境温度下进行70 ℃耐久性试验,而且阻值变化不超过该试验的允许值时所允许的最大功耗。 |
| 类别功耗 | category dissipation | IEC 60115-1 | fraction of the rated dissipation exactly defined by the relevant specification, applicable at the UCT, taking into account the derating curve prescribed by the relevant specification. |
| GB/T 5729 | 考虑到详细规范规定的降功耗曲线,由详细规范明确规定的在上限类别温度下施加的那一小部分额定功耗。 |
| 功率降额曲线 | derating curve | IEC 60115-1 | curve that shows the maximum allowable dissipation at ambient temperatures between the UCT and the LCT. |
| 表征在类别上限温度与类别下限温度之间各环境温度下,电阻器最大允许功耗的曲线。(在LCT至额定温度区间内,曲线对应额定功耗;在额定温度至元件最高温度MET区间内,曲线先行下降,至MET处功耗降为0,该下降斜率由电阻器热特性即向环境散热的能力决定) |
| 长期寿命 | endurance (load life) | IEC 60115-1 (无定义,仅作为测试项目) | 测试在规定温度下(70 ℃或室温),长期循环施加特定电压后,电阻器仍能保证正常工作且阻值稳定的能力。 |
|
| 短时过载 | short-term overload | IEC 60115-1 (无定义,仅作为测试项目) | 考核电阻承受单次短时过载的耐受能力。 |
|
| 上升时间(电感) | rise time(inductive time constant τL) | IEC 60115-1 (无定义,仅作为测试项目) | 施加脉冲电压时,电阻上的电压达到最大电压一定程度所需的时间。 |
| (根据IEC 60115-1中的测试方法,需要测量通过测试系统读出的电压达到最大电压63.2%时的时间) |
| (仅适用于低电感电阻) |
| 电流噪声 | current-noise | IEC 60195 | combination of all random fluctuations of current flow in a resistor which are not attributed to thermal agitation of the charge carriers (thermal noise) and which depend on the applied direct current. |
| 电阻中所有电流随机波动的组合,这些波动不源于载流子的热运动(热噪声)且与施加的直流电流有关。 |